Products
YUSIN speed control motor special simple regulator:
| Motor power: | 6W-15W-25W-40W-60W-90W-120W-200W |
| Single-phase voltage: | 100V-110V-115V-12 0V-127V-220V-240V |
| Three-phase voltage: | 200V-220V-230V-240V-380V-400V-415V-440V |
| Voltage Frequency: | 50HZ /60HZ |
| Speed reduction ratio: | 1/3-1/1800 |
| Output speed: | 0.1-1450RPM |
| Output Torque: | 0.1-120N.m |
| Motor Function: | Standard fixed speed motor - reversible fixed speed motor - adjustable speed motor - electromagnetic braking Motor - adjustable speed electromagnetic brake motor - torque motor |
| Can match the gearbox type: | H standard gearbox, GM intermediate gearbox, RC right angle hollow gearbox, RT right angle real gearbox, HE standard gearbox (with ear type) |
Product characteristics:
1. Due to the use of speed controller, can obtain a wide range of variable speed (50Hz ... 90 to 1400 ret/min; 60Hz...... 90 to 1600 ret/min).
2. Can be selected on demand variable speed, electronic braking, conversion positive. inverse, slow acceleration, slow deceleration and other complex operating procedures.
3. Equipped with speed sensor, closed-loop control, speed and voltage frequency independent. The analog voltage of 0 to 10V can be directly entered to control the speed, which is easy to connect with the PLC.
YUSIN brand fan (blower) installation and use method：
When the high-voltage fan is running, the current consumed by the motor increases with the increase of pressure and vacuum, such as the current is too large will cause the contactor to jump off, in order to prevent jump or power saving, please maximize the area of the air output, or in the suction or exhaust side installation of the air pressure air volume control valve.
A、Air feed - The entrance should be filled with an appropriate filter
1、The total cross-sectional area of the air-out hole shall be greater than 1/2 of the wind turbine outlet cross-sectional area.
2、If used for air delivery in water, its water depth pressure should be less than 70% of the maximum static pressure value indicated in the model catalogue.
3、When the pressure is sent, the outlet temperature due to air friction is greater than 10 degrees Celsius is normal, so the iron pipe should be used more than 1M.
B、Suction - The total area of the silencer suction hole may be added at the outlet shall be greater than 1/2 of the area of the blower inlet.
C、Easy way to clean up filters：
Turn the filter from the connector and remove dirt or dust from the filter with an air spray gun or brush, which can be used when cleaned.
D、Installation site
The ambient temperature and humidity should meet the following conditions：
1、Single-phase -5 to 40 degrees C three-phase -10 to 40 degrees C.
2、Choose a place with good ventilation, less dust and moisture.
3、For those installed in the open air, use a rain cover.
E、Installation method
High-pressure fan can be installed at any angle, with screws really fixed to the horizontal and rigid foundation or base. The base weight is about 3 times the standard for high-pressure fans. Special attention should be paid to whether the base is uneven, if so, when the bolt twists, the high-pressure fan table may be deformed! Shock absorbers can be added to reduce noise. When the air vents are not connected to the suction port, add barbed wire to prevent dangerous or foreign inhalation.
E-series
Yusin L series miniature inverter product features:
Embedded installation, simple and beautiful output frequency 0.1-800Hz can not be determined V/F curve
Output frequency 0.1 - 800Hz various display states freely switch rich external terminal function carrier frequency up to 12kHz
Automatic torque lift and automatic slip compensation
Full protection (overpressuring, underpressuring, overflow). Overload, short-circuit protection) built-in Modbus485 up to 115200bps
Single-phase asynchronous motors can be driven
